4000.00 $ FS/FT HF 12x36 Lathe. Lots Of Tooling. Ainsworth

Published date: June 1, 2024
  • Location: Ainsworth, Iowa, United States

FS/FT HF 12x36 Lathe. Lots Of Tooling.


⭕ Looking to sell or trade my 12x36 lathe. (Model # 65044) This is the same as the Grizzly G4003 except this one has 18 speeds.

This has a 1.5 spindle bore.

Lathe is driven by a 1.5hp 1750rpm Reliance 208V 3 phase motor. 3 phase power is provided via Teco L510 2hp VFD using 230V single phase.

Ive programed the VFD for forward and reverse inching at 10hz.

Speed is variable via the potentiometer on the control panel.

Max frequency is set at 60hz, but can be easily changed.

I have installed a locking mushroom head e-stop button for disconnect from the 230V line. There is also a 30A din mounted breaker for over current protection inside the box. A 230V pilot light indicates power to the VFD.

The forward and reverse switch functions as it normally would on these lathes.

I have installed a MachTach using an IR sensor to show spindle RPM. This unit will show rpm or SFM with a push of a button.

All electronics have been rerouted to the J-box shown in the picture. I have had no issues with heat dissipation from the VFD.

I will provide a wiring diagram with the lathe. All used terminals are labeled and listed on the diagram.

The lathe includes:

The factory stand.
All factory tooling.
1- AXA QCTP that is the wedge design.
1- AXA QCTP that is the piston design.
10- AXA QCTP tool holders.
1- 2 axis DRO from Tpactools. (Best addition ever)
1- MachTach Tachometer reading spindle rpm.
1- D1-4 Tru-set collet Chuck from Lathemaster. (5C collets)
1- set of 65 5C collets from 1/8 to 1-1/8 from CDCO. (Imports, but have been accurate from what Ive seen so far)(Majority are still in the wrapping)
1- set of 23 5C collets from 3mm to 25mm.
1- 1/2 CTAP indexable tool holder. (TPG-222 inserts. Clamping, not the screw in inserts)
10- TPG-222 inserts
1- 5/8 external indexable threading tool.
1- 1/2 internal indexable threading bar.
1- 5/8 3MT Jacobs drill chuck.
1- magnetic base dial indicator holder.
I also have a large amount of HSS cutters that will go if you want them as well.

I have had zero issues with this lathe after the VFD install. The surface finish provided by the 3P motor is excellent. The ways are in great shape and show no obvious wear or abuse. There are no oil leaks on this lathe.

The lathe is under power and can be tested anytime.

Ill consider almost anything in trade. A smaller extremely well tooled lathe would be preferred. I do not need a mill however.

This is a complete package. I will not split any tooling.

The lathe is sitting as shown in the picture.

I have an engine hoist and rigging on hand to load the lathe.

Text, or email with any questions or offers of a trade.

Thanks,
Austin


Phone number ✆ +1 712-452-7572

Ainsworth, Iowa

Contact seller Share

Related listings

  • Ryobi Saws All
    TOOLS - Janesville (Iowa) - June 30, 2024 25.00 $

    Ryobi Saws All ⭕ Just like new barely used. Works perfect. Phone number ✆ +1 712-246-3981 Janesville, Iowa

  • **freelander{ 300cc 4x4 Atv } Features Electric Start****
    TOOLS - Shellsburg (Iowa) - June 29, 2024 4199.00 $

    **freelander{ 300cc 4x4 Atv } Features Electric Start**** ⭕ FREELANDER 300CC 4X4 ATV FEATURES ELECTRIC START.A GREAT OUTDOOR POWERSPORTS UNIT. THE FREELANDER 300CC 4X4 ATV FEATURES ELECTRIC START, GAS POWERED, 4 WHEEL DRIVE, REVERSE, FULLY AUTOMATIC ...

  • Router Table
    TOOLS - Stanwood (Iowa) - June 29, 2024 10.00 $

    Router Table ⭕ Hersh router table 10.00 calls only please 861-0874 Gary Phone number ✆ +1 641-585-8755 Stanwood, Iowa

  • Craftsman Radial Arm Saw Laser
    TOOLS - Salix (Iowa) - June 29, 2024 450.00 $

    Craftsman Radial Arm Saw Laser ⭕ Works great only used a few times on wheels for easy moving around the shop retails for 1000 at Sears Phone number ✆ +1 515-439-2688 Salix, Iowa

  • RYOBI WET TILE SAW
    TOOLS - Ringsted (Iowa) - June 29, 2024 95.00 $

    RYOBI WET TILE SAW ⭕ Hello, for sale is a RYOBI tile saw complete with box, paperwork and attachments! This was used once for 16 cuts to replace a few tiles. I am asking $95 obo! Feel free to ask any questions and thanks for looking! Phone number ✆ +...

  • Car Waxer For Sale
    TOOLS - Zearing (Iowa) - June 28, 2024 20.00 $

    Car Waxer For Sale ⭕ I have a car waxer for sale. Its used and works great. Asking $20 firm. Phone number ✆ +1 319-329-4668 Zearing, Iowa

  • HUSKY 3/8 DRIVE SET
    TOOLS - Brighton (Iowa) - June 28, 2024 28.00 $

    HUSKY 3/8 DRIVE SET ⭕ HUSKY TOOL SET WITH HARD CASE GREAT TO CARRY IN TRUCK ON BOAT OR JUST ANY WHERE. AMERICA STANDARD NO CALLS AFTER 9 PM 540-FOUR 93-7279 Phone number ✆ +1 641-387-6968 Brighton, Iowa

  • Sewer Fan
    TOOLS - Silver City (Iowa) - June 27, 2024 50.00 $

    Sewer Fan ⭕ Gas powered sewer fan, goes in place of sewer lid and used to smoke sewers. Gas motor runs Daniel 859 9 nin l 96○7 Phone number ✆ +1 563-949-1956 Silver City, Iowa

  • Craftsman Electric 18 Chain Saw
    TOOLS - Blanchard (Iowa) - June 27, 2024 100.00 $

    Craftsman Electric 18 Chain Saw ⭕ When it comes to working around your yard, the Corded Electric 18 in. Chainsaw is so handy. You can prune your bushes, saw through large branches, take down small trees and get your yard and garden area looking well ...

  • Milwaukee 0299-20 Magnum 8 Amp 1/2-Inch Drill
    TOOLS - Meservey (Iowa) - June 26, 2024 50.00 $

    Milwaukee 0299-20 Magnum 8 Amp 1/2-Inch Drill ⭕ Milwaukee 0299-20 Magnum 8 Amp 1/2-Inch Drill in good condition. 909-837-857o Phone number ✆ +1 515-644-6639 Meservey, Iowa

  • Swingline Glue Gun, Campbell Paint Sprayer, And Weller Solder Gun
    TOOLS - Cumberland (Iowa) - June 26, 2024 30.00 $

    Swingline Glue Gun, Campbell Paint Sprayer, And Weller Solder Gun ⭕ Hello. We have a few things available for immediate sale. A vintage Swingline Glue Gun, called The Little Red Fixer w/glue sticks. A Campbell Hausfield Paint Sprayer, the type that c...

  • USED 8,000 LB TCM FHG36N2T Pneumatic Forklift
    TOOLS - McIntire (Iowa) - June 26, 2024 18500.00 $

    USED 8,000 LB TCM FHG36N2T Pneumatic Forklift ⭕ This is a heavy duty forklift thats capable of lifting 8000 pounds. It has four brand new solid pneumatic tires, a new starter, a new hydraulic pump, and a rebuilt control valve. The fuel system is all ...

  • FOR SALE 1 HP CRAFTSMAN AIR COMPRESSOR
    TOOLS - Swea City (Iowa) - June 26, 2024 100.00 $

    FOR SALE 1 HP CRAFTSMAN AIR COMPRESSOR ⭕ FOR SALE 1 HP AIR COMPRESSOR CRAFTSMAN WORKS GREAT , FOR MORE INFORMATION CALL Phone number ✆ +1 712-820-6312 Swea City, Iowa

  • Mixpac Solid Surface Gun
    TOOLS - Le Mars (Iowa) - June 26, 2024 100.00 $

    Mixpac Solid Surface Gun ⭕ Mixpac Solid surface gun, 100 or OBO, barely used, comes with 10 tips. This is the best gun in the industry! Phone number ✆ +1 563-733-5346 Le Mars, Iowa

  • Powermatic 8 Jointer
    TOOLS - Bedford (Iowa) - June 25, 2024 400.00 $

    Powermatic 8 Jointer ⭕ Powermatic 8 jointer with 1 h.p., 3 phase Baldor motor. $400 Robert 210200 American, american woodworking, boice crane, bridgeport, buffalo, buss, canedy otto, carlton, cincinati, clausing, clement, colladay, comet, crescent, c...

Comments

    Leave your comment (spam and offensive messages will be removed)